Automotive computer flash programming tool install#
Automotive computer flash programming tool software#

Automotive computer flash programming tool install#

Step 4: Once downloaded install the software, make sure yourВ STM32В board is connect to your computer thoughВ FTDIВ board and then launch the software. DonвЂ™t forget to check your spam folder for the E-mail, sometimes it takes a couple of minutes for the E-mail to arrive. Yes itвЂ™s a bit frustrating but this is how it should be done.

Automotive computer flash programming tool software#

Then follow the link back to the website and click on get software again and you download will begin. Step 3: To download the software you have to enter your E-mail address and the download link will be sent to your E-mail. Click on this linkВ to get into the ST website and scroll to the bottom and click on get software Step 2:В Next we have to download and install theВ STMВ Flash loader software to flash the downloaded bin file intoВ STM32. There are many versions of bin file, for the Blue Pill board use this github linkВ and click on the download button to download the bin file. Step 1:В We have to download the boot loader program file binaries (bin file) form the github page. Once we have made the above connection connect theВ FTDIВ board to your computer and follow the steps to flash the boot loader into theВ STM32. Uploading the Maple Boot loader toВ STM32В Development board Once the boot loader is flashed this pin can be changed back to initial position (operating mode). Make sure the boot 0 jumper pin on the board is set to 1 (programming mode) while uploading the boot loader. Where the A9 is the Tx pin ofВ STM32В MCUВ and theВ A10В is Rx pin. The Rx and Tx pin of theВ FTDIВ board is connected to the A9 andВ A10В pin of theВ STM32В respectively. The ground is connected to the Ground ofВ STM32. TheВ VccВ pin of theВ FTDIВ board is connected to theВ STM32В 5V pin of power the board. This board is connected to the Rx and Tx pin of theВ STM32В as shown below. To do this we need to use a SerialВ FTDIВ board. To program theВ STM32В Blue Pill board directly through USB portВ we need to first flash the Maple boot loader into theВ MCU. STM32В вЂ“ (BluePill) Development Board ( STM32F103C8).Before proceedings with this tutorial make sure you have read the previous tutorialВ to understand the basics of this board including details about the specifications and pin-outs. However this boot loader is still in developmental stage at the time of documenting this tutorial and is not advisable for critical applications. This boot loader can be flashed into theВ STM32В once and thereafter we can directly use the USB port of theВ STM32В board to upload programs just like any otherВ ArduinoВ boards. Hopefully though, there exists an experimental boot loader developed by LeafLabsВ for Maple mini boards. The reason for doing that is, when theВ STM32В development board is purchased it does not come with anВ ArduinoВ ready boot loaderВ and hence the board will not be discovered by your computer when connected through the USB. Also the mini-USB port on the Development board was left totally unused. In order to program the Board weВ utilisedВ aВ FTDIВ programmer module and also had to toggle the boot 0 jumper between and 1 position while uploading and testing a code, which is surely a daunting task. In our previous tutorial we learnt the basics of theВ STM32В Development BoardВ and alsoВ programmedВ it to blink an LED. Also since, this board can be easilyВ programmedВ using theВ ArduinoВ IDE it has become a preferable choice for many hobbyists and engineers for quick prototyping. The STM32В Development Board housing the STM32F103C8В Microcontroller is getting increasingly popular thanks to its ARM Cortex M3 architecture, it has high operational speed and more peripheral options.